 Hello, Here is a guide to help you see what you are in for when doing the job with diagrams below of the camshaft sensor location for both engines. https://www.2carpros.com/articles/camshaft-angle-sensor-replacement Check out the diagrams (Below). Please let us know if you need anything else to get the problem fixed. Cheers Image (Click to enlarge) SPONSORED LINKS Friday, January 2nd, 2009 AT 11:45 AM NOSCOT
Have a 2002 jeep grand cherokee 4.0L when starting it just cranks first 2 trys when starting then turns over 0n 3rd try-runs great after it starts, where is crankshaft sensor located on this eng. And is it difficult repair Monday, December 7th, 2020 AT 9:13 AM (Merged) Check fuel pump and fuel pressure Monday, December 7th, 2020 AT 9:13 AM (Merged) HEEEEETHIN
Other Category problem can not find where this litlle item is located if you could give me an exact location it would greatly be appreciated Monday, December 7th, 2020 AT 9:14 AM (Merged) It's on the transmission Bell housing, left side... SPONSORED LINKS Monday, December 7th, 2020 AT 9:14 AM (Merged) Its on the left side of the transmission bellhousing see below. Is there anything else I can help you with? Monday, December 7th, 2020 AT 9:14 AM (Merged) Get me a cold BEER! Monday, December 7th, 2020 AT 9:14 AM (Merged) Hey Mike When I post this reply my monitor flashes then it opens then here you are-Wow! Kind of freaky. For some reason were hitting the same subject at the same time. Sometimes I win and sometimes I lose. Drink 1 for me will you-its nite time there for it. Monday, December 7th, 2020 AT 9:14 AM (Merged) JIM FRY
Engine Mechanical problem 01 grand cherokee 4.7 v-8 where is it located Monday, December 7th, 2020 AT 9:14 AM (Merged) On right side of engine block,above starter motor. Monday, December 7th, 2020 AT 9:14 AM (Merged) D12345ODGER
Check engine light came on, diagnosed as crankshaft position sensor, where is it? Monday, December 7th, 2020 AT 9:14 AM (Merged) Right side engine block above starter SPONSORED LINKS Monday, December 7th, 2020 AT 9:14 AM (Merged)
My 1999 did the same thing and the sensor is in an impossible spot to fix on the bottom of motor above the transmission. I was told that if the vehicle isn't acting up don't fix it. Somewhat of a dummy light. Monday, December 7th, 2020 AT 9:14 AM (Merged) SAM WELLS
Where is the crankshaft positioning sensor on the 2000 cherokee 4.0 engine? Do you have to pull the starter to change it? Monday, December 7th, 2020 AT 9:14 AM (Merged) Welcome to the forum, my info shows this for crank sensor location. Monday, December 7th, 2020 AT 9:14 AM (Merged)
It's in a horrible spot and it's a common Dumby check engine readout. If the car runs good don't replace it Monday, December 7th, 2020 AT 9:15 AM (Merged) MADLPN
Noises problem My 99 jeep grand cherokee dies if it goes below 1000 rpms and if it goes above 2000 rpm it constantly jerks. Also the oil pressure gauge is not working properly at times it will fluctuate between 20-40 but most times it stays near 0. My ex husband just recently replaced both the ignition coil and the crank shaft sensor unit in the last 3 months. A mechanic friend told me to get in the jeep and turn the ignition key on then off and then on and off and then on and watch for anything to pop up such as the check engine light flashing and count the flashes I did try this but what I got from the dash controls was where the mileage is this appeared "P 0352 P 1391 done" done this mean anything and what is the best thing to do. Also today the trans over temp light came on and the overdrive off light came on. Once I turned the vehicle off for a while and restarted it this went off. Monday, December 7th, 2020 AT 9:31 AM (Merged) P0352 is for the coil being faulty and the P1391 is for the cam and crank sensors being faulty but befor you change them change the spark plugs and wires cap and rotor then try it if it still has probblem then you are looking at changing the sensors and coil Monday, December 7th, 2020 AT 9:31 AM (Merged) What are the symptoms of a failing crankshaft position sensor?Symptoms of a Bad or Failing Crankshaft Position Sensor. Issues Starting the Vehicle.. Intermittent Stalling.. Check Engine Light Comes On.. Uneven Acceleration.. Engine Misfires or Vibrates.. Rough Idle and/or Vibrating Engine.. Reduced Gas Mileage.. Will a crankshaft sensor keep a car from starting?If the crankshaft sensor is not working correctly, the engine will not run. The engine will not be able to start and will stall. Even if the engine does start, it will likely misfire and run rough.
|
2003 jeep grand cherokee 4.0 crankshaft position sensor location
Related Posts
Copyright © 2024 moicapnhap Inc.
