2013 jeep grand cherokee oil type

For 2013 Grand Cherokee Fourth generation Jeep recommends to use: MS-6395, MS-10725, and ACEA C3 engine oils. To select the right engine oil see the table below.

How much engine oil you need to put into 2013 Grand Cherokee depends on conditions listed below.

car Add this car in your garage to make future searches easy.

ConditionVolume3.6 V6 4x4 with gasoline V6 3.6 L 282 HP engine (2010.11–)5.92 US qt.4.93 UK qt.5.6 LEngine oil: MS-63953.6 V6 FlexFuel 4x4 with gasoline V6 3.6 L 282 HP engine (2010.11–)5.92 US qt.4.93 UK qt.5.6 LEngine oil: MS-63953.6 VVT 4x4 with gasoline V6 3.6 L 286 HP engine (2010.10–)5.92 US qt.4.93 UK qt.5.6 LEngine oil: MS-63955.7 V8 4x4 with gasoline V8 5.7 L 347 HP engine (2010.11–)6.97 US qt.5.81 UK qt.6.6 LEngine oil: MS-63956.4 SRT8 4x4 with gasoline V8 6.4 L 461 HP engine (2011.3–)6.97 US qt.5.81 UK qt.6.6 LEngine oil: MS-10725All other modifications8.88 US qt.7.39 UK qt.8.4 LEngine oil: ACEA C3

Replacing engine oil in your 2013 Jeep Grand Cherokee is quite an easy task. It's a bit dirty, but everyone can handle it. It will take about 3060 minutes depends on your skill level and might save you $10$30 depends on the region you live in.

First unscrew the refill cap on the top of the engine. Use a ratchet with the correct size head to unscrew the drain plug on the engine oil pan located on the bottom side of the engine, and drain old oil. You might need to unscrew a few more screws to remove protection covers underneath your car to get access to the oil pan and the oil filter. Then using an oil filter wrench unscrew the old oil filter. Then lubricate a new filter rubber gasket with clean engine oil and install the new filter. Install a new drain plug, and with help of a funnel refill the engine with new engine oil.

Please be noted that all capacities listed here are approximate. Check fluid levels when adding or refilling as recommended in your 2013 Jeep Grand Cherokee user's manual. Keep in mind that all information here is provided “as is” without any warranty of any kind.

Before doing any DIY service please check your insurance policy and Jeep warranty policy for your region. In some regions DIY service may invalidate your warranty.

Table of Contents

  • Air Conditioning Refrigerant Capacity
  • Automatic Transmission Fluid Capacity
  • Axle Oil Capacity
  • Brake Fluid Capacity
  • Cooling Fluid Capacity
  • Engine Oil Capacity
  • Fluid and Lubricant Specifications
  • Gearbox Oil Capacity
  • Steering Fluid Capacity
  • Brake System Specifications
  • Chassis Specifications
  • Cooling System Specifications
  • Electrical System Specifications
  • Emission
  • Maintenance Items
  • Chassis and Body Fastener Tightening Specifications
  • Engine Fastener Tightening Specifications
  • Front Suspension Fastener Tightening Specifications
  • Rear Suspension Fastener Tightening Specifications
  • Transmission Fastener Tightening Specifications
  • Service Intervals

Conquer your fears and never give up!

DIY car service is not as difficult as it looks like and it might save you thousands of dollars per year. It might be even fun and a good thing to do with your kids on a weekend to teach them how basic machinery works. It's really hard to screw something up and damage your car permanently if you use right tools, follow Jeep Grand Cherokee service manual and use right parts and fluids in prescribed amounts. Even modern cars stuffed with electronics can be serviced in your garage or even in your driveway. Changing engine oil, brake fluid, ATF, replacing brake pads, and etc. It's all may be done by yourself in a mater of a couple of hours.

Doing basic service for your 2013 Jeep Grand Cherokee you're not only saving money, but also also improving your technical skills and learning something new.

At the heart of every vehicle, the Grand Cherokee engine needs motor oil for it to perform properly and meet or exceed its lifespan. Motor oil protects, cleans, lubricates, and cools down the engine, but you must make sure you use the right type. If not, you might end up spending a considerable amount of money on repairs or worse; the engine gets damaged completely.

So, what Jeep Grand Cherokee oil type should you put in the engine? The specific engine oil to purchase and use depends on your Grand Cherokee’s year model and engine type. The good thing is that Jeep usually provides these specifications for you.

Although most people entrust your car to professionals, it is best to know what kind of oil it needs because you might forget to check its level and need to refill it in the middle of nowhere or while off-roading. Also, part of your car’s regular maintenance is an oil change, and you must know when it needs one. This Jeep Grand Cherokee oil type guide will provide those bits of information on the most popular year models of the Grand Cherokee.

2013 jeep grand cherokee oil type

What Type of Oil Does a Jeep Grand Cherokee Take?

Motor oil is available in several types, including conventional or petroleum-based, full synthetic, synthetic blend, and high-mileage, but what you’ll need will depend on your car’s engine. The Grand Cherokee year models we focused on in this guide all have gas-powered engines but have different oil capacities and specific oil requirements that you need to be familiar with.

General Types of Motor Oil

For the Jeep Grand Cherokee models we looked at, they require full synthetic oil, except for two. Specifically, the 1996 Jeep Grand Cherokee oil type requirement is high-mileage, while the 1999 Jeep Grand Cherokee oil type recommendation is conventional. As such, we’ll only discuss the three types in detail so that you have a better understanding of how they differ.

1. Conventional

Conventional or mineral oil is made from refined underground crude oil and meant for cars with simple designs and drivers with regular driving styles. This oil is more affordable than the others, but quickly thickens in low temperature and thins out at high temperature. It is also a type of oil that is prone to sludge and tar-like-deposit buildups, so your car will require more maintenance.

2. Full Synthetic

The Jeep Grand Cherokee is a vehicle that you usually drive on rough terrains and use for heavy-duty jobs such as hauling or attaching your snowmobile trailer, so most models require synthetic oil. It is a type of oil that has better lubricating, impurity removing, sludge buildup prevention, and heat-resisting properties. It is also less affected by temperature changes.

Synthetic is 1998, 1999, 2001, 2002, 2006, 2018, and 2019 Jeep Grand Cherokee oil type requirements because it is less affected by temperature changes, helps improve fuel efficiency, and aids in increasing horsepower. An enormous list of capabilities that you need for safer and better off-roading adventures.

3. High-Mileage

Aptly named, this is an oil meant for vehicles with high mileage, usually between 75,000 and 100,000. It has additives for better extreme temperature, sludge buildup, leak, and wear protection.

Specific Oil Types

2013 jeep grand cherokee oil type

Any motor oil comes in different viscosity levels, which will help determine how they can improve your car engine’s performance. To ensure manufacturers are producing similar oil quality, the SAE (Society of Automotive Engineers) created a standard grading system for both single- and multi-grade oils.

Since the Jeep Grand Cherokee models usually require multi-grade oil, we’ll focus on it. When choosing the right one for your car, here are the factors to keep in mind:

1. Temperature or Weather

Aptly named, multi-grade oil has two grades, which refers to the oil’s viscosity in low- and high-temperature ranges. They are:

  • The “W” Grade
    The motor oil’s “W” grade is the number you’ll see before the letter “W”, which refers to the product’s cold viscosity. This grade is the oil’s thickness when you cold start your car’s engine or the time before fuel combustion and the ignition warm up the engine block.

    For example, the 0W in the 2018 Jeep Grand Cherokee oil type requirement has a lower viscosity than the 5W 2001 Jeep Grand Cherokee oil type recommendation. That means the 0W flows better than the 5W during cold weather conditions or in areas with winter seasons, so it clings to the moving parts better, lubricating them more efficiently.
  • The Single Grade
    The single grade or second number found on multi-grade engine oil refers to its viscosity when it reaches its operating temperature, and when the engine is warm already. At this point, the car engine will require oil with higher viscosity grades for better lubrication. Thus, if you live and drive in areas with usually hot climates, it’s better to choose a 5W-30 oil than a 5W-20.

2. Fuel Economy

The engine oil’s viscosity grade also plays a role in fuel-efficiency. Low-viscous oil helps you save on fuel more since there is less engine friction. The disadvantage you need to consider is that your car’s engine will wear faster and require more frequent maintenance than engines that use high-viscous oil.

3. Age of Engine

High-mileage oil for older and second-hand vehicles are also available in different viscosity levels or grades. Since you’re driving a Grand Cherokee with an “old” engine, you should expect that the block and cylinders are looser and have more space between them than ones found on newer engines. With that in mind, highly viscous engine oil would lubricate the parts better to reduce the occurrence of further wear and tear, increasing the engine’s lifespan.

Now that you have a good understanding of the general and specific kinds of motor oil, let us look into the specific 1996 Jeep Grand Cherokee oil type, 1998 to 1999 Jeep Grand Cherokee oil type, 2001 to 2002 Jeep Grand Cherokee oil type, 2006 Jeep Grand Cherokee oil type, and 2018 to 2019 Jeep Grand Cherokee oil type recommendations.

ModelEngine TypeOil Capacity
(Quarts or Liters)Specific Oil Type19964.0L L66qts. or 5.7LSTP 10W-30 High Mileage19985.2L V85qts. or 4.7L5W-30 Synthetic19995.9 V85qts. or 4.7L5W-30 Conventional20014.0L V66qts. or 5.7LSAE 5W-30 Synthetic20024.0L V6
4.7L V8 (Code [J] J)
4.7L V8 (Code [N] N)6qts. or 5.7L5W30 (Below 100F) or
10W30 (Above 0F)
Synthetic20063.7L V6
4.7L V8
5.7L V85qts. or 4.7L
6qts. or 5.7L
7qts. or 6.2L5W30 Synthetic
5W20 Synthetic
20182.4L 4-Cylinder
3.2L V65.5qts. or 5.2L
5.9qts. or 5.58LSAE 0W-20 Synthetic20193.0L V6
3.6L V6
5.7L V88.1qts. or 7.66L
5.9qts. or 5.58L
7qts. or 6.2L5W-40 Synthetic
0W-20 Synthetic
5W-20 Synthetic

Keep in mind that although the data provided are too specific, it is not restrictive, like for the 2018 Jeep Grand Cherokee oil type, which is 0W-20 synthetic, you may switch to one with a slightly higher viscosity, but not too high, depending on the factors mentioned above. However, make sure you don’t shift from one oil type to another without getting the approval of a professional or the manufacturer’s service center.

When Should I Change the Oil in My Jeep Grand Cherokee?

Knowing and using the right type of motor oil isn’t enough to ensure your Grand Cherokee’s engine performs at its best. You must also schedule regular oil changes to keep the engine clean, fuel-efficient, and at low temperature, as well as to protect its parts from corrosion and prevent engine knocking.

Whether you do the oil change yourself or let a professional handle it, especially if it’s still under warranty, you need to check to determine if your car needs an oil change through the following:

1. Mileage Reading

Jeep and any other manufacturers have oil change frequency recommendations based on your car’s mileage. It usually depends on the car model’s oil type requirement like for the 1998 Jeep Grand Cherokee oil type, which is conventional, it would require an oil change every 3,000 to 5,000 miles of use. On the other hand, for models needing synthetic oil, the frequency is every 7,500 to 10,000 miles.

2. Oil Change Sticker

It is a common practice of mechanics and auto-shops to place an oil change sticker to remind the car owner of the next oil change schedule: date and/or mileage. Usually, you’ll find the sticker on the windshield, so it is the quickest and easiest source of information in terms of the oil change schedule.

3. Oil Change Reminder Light

Your Grand Cherokee has multiple indicator lights, and newer models usually have an oil change reminder light. When your car reaches a particular mileage, it will light up automatically to remind you that it needs an oil change.

Since the mechanic will manually reset this every oil change, you must distinguish if it is truly time for an oil change or the mechanic just forgot to reset it. You can do so by comparing it with the mileage and/or the oil change sticker.

4. Engine Noise

When the oil is at a low level and/or no longer viscous, there would be friction between the engine parts, causing tapping or knocking sounds. To determine whether it needs an oil change or just an additional oil, you should perform a dipstick oil analysis.

With the engine off, open your Grand Cherokee’s hood and search for the dipstick, and then pull it out from your car engine and wipe away excess oil. Carefully insert it back into the designated tube and push it slowly. Pull it out and check the oil level and quality.

If the oil is too dark, almost black, it signifies that you need an oil change. On that note, whether or not you need an oil change, if the oil level is low, you need to add more, making sure you don’t exceed your 1996, 1998, 1999, 2002, 2006, 2018, 2019, or 2001 Jeep Grand Cherokee oil capacity.

So how low is too low? The dipstick has markings for full, safe, and low levels. No matter what type of engine your Jeep Grand Cherokee has and the oil it requires, it can still run, especially on flat and smooth terrains, when the oil mark is at the low level or approximately one quart.

However, expect that it would already cause minimal damages to your car engine parts, so it would be best to refill the missing amount. Having a rugged storage box (view on Amazon) where you can place all your car emergency tools and extra engine oil is a good idea, especially if you’re off-roading regularly.

Jeep Grand Cherokee Oil Type: The Takeaways

Much like any other vehicle, your Jeep Grand Cherokee is an investment, so it deserves all the care and maintenance. Engine oil has a vital role in your vehicle’s performance, so you must make sure that you use the type of oil recommended by the manufacturer or a different grade approved by a professional. You must also not forget your Grand Cherokee’s oil change schedule and refills.

One last tip: during oil changes, it is also best to change your engine’s oil filter. If you’ve already mastered this maintenance skill and you’re car isn’t on warranty anymore, you can purchase a quality oil change kit and do things on your own.

What kind of oil does a 2013 Jeep use?

Per Owner's Manual the 3.6L Pentastar engine in the 2013 JK takes 6 quarts of 5W-20 motor oil. Experience put the fill at just a little under this (about 5.6 quarts). Perhaps 0.4 quart is retained during the change.

How much oil does a Jeep Grand Cherokee 3.6 take?

You need 5.0 quarts of oil to keep your Jeep 3.6 running like new. But what kind of oil should you use?

What oil type does a Jeep Grand Cherokee take?

The 2022 Grand Cherokee comes with either a 3.6-liter V6 engine or a 5.7-liter Hemi V8. For the V6 engine, you'll need 0W-20 synthetic oil. For the V8 engine, you'll need 5W-20 synthetic oil.

Does Jeep Cherokee need synthetic oil?

For example, a 2019 2.0L V6 Cherokee will require 5W-40 synthetic oil, whereas a 2018 3.2L V6 Cherokee requires SAE 0W-20 synthetic oil. Referring to the owner's manual is the best way to find out which oil is recommended for your Cherokee. It is recommended to check your engine oil levels while the engine is cold.