If you have no fuel or spark then you most likely have a crank sensor issue.
Here is a guide that will help this:
//www.2carpros.com/articles/symptoms-of-a-bad-crankshaft-sensor
The crank sensor is used for spark and injector pulsing and the cam sensor is used to help time those pulses so if you are not getting them then it is likely the crank sensor.
When you crank the engine does the tach go up slightly?
If it were me, I would replace the crank sensor with a Mopar sensor and retest. Off brand sensors by have an issue out of the box giving you the thought that it is not the CKP sensor.
I attached the info below on these sensors.
Please run through this info and let us know if you have questions. Thanks
Images (Click to enlarge)
SPONSORED LINKS
Thursday, July 29th, 2021 AT 6:42 PM
Welcome, 3.9L engine, should be in the distributor. Check out the diagrams (Below). Please let us know if you need anything else to get the problem fixed.
Image (Click to enlarge)
SPONSORED LINKS
Saturday, October 10th, 2009 AT 10:08 AM
TIFFLOVESJEFF
- MEMBER
- 1995 DODGE DAKOTA
- 6 CYL
- 2WD
- AUTOMATIC
- 160,000 MILES
Where are the crankshaft position sensor and the camshaft position sensor located on my 1995 Dodge Dakota Automatic 6 cylinder?
Monday, March 4th, 2019 AT 11:26 AM (Merged)
Crank sensor is in the transmission bell housing right behind the right cylinder head. Cam sensor is in the distributor.
Caradiodoc
Monday, March 4th, 2019 AT 11:26 AM (Merged)
VINCET TELLEZ
- MEMBER
- 2005 DODGE DAKOTA
Engine Performance problem
2005 Dodge Dakota V8 Two Wheel Drive Automatic 51.991 miles
Where are these located at?
Monday, March 4th, 2019 AT 11:26 AM (Merged)
Cam sensor assuming its a 4.7 is on the passenger side of the engine, towards the front and top of the cylinder head. Crank sensor is also on the passenger side of the engine located just under the exaust manifold closest to the rear of the engine, just under a freeze plug.
SPONSORED LINKS
Monday, March 4th, 2019 AT 11:26 AM (Merged)
Joined
Apr 19, 2011 · 10 Posts
Discussion Starter · #1 ·
Jul 6, 2011 Trying to replace a cam shaft position sensor on my 2001 dodge durango. Can't find where it's at. Every place I see on Google says inside the distributor, but this engine doesn't have one. Any help would be great! Joined Jun 20, 2008 · 601
Posts
If you do not have a distributor, you have the 4.7 engine. (The 5.9 does have one.) On the 4.7 engine, The Camshaft position sensor is on the underside of the right side head, near the front of the engine. Joined Dec 8, 2009 · 1,234 Posts
If you do not have a distributor, you have the 4.7 engine. (The 5.9 does have one.) On the 4.7 engine, The Camshaft position sensor is on the underside of the right side head, near the front of the engine. You can (unless you've got huge arms and wrists). I found it easier to remove the sensor bolt from above, but remove and replace the sensor itself from the ground, laying on my back. YMMV. Joined Dec 31, 2013 · 4 Posts
So is it on the same side as the crank sensor?
Joined Jun 20, 2008 · 601 Posts
Yes, but at the front of the engine.
Thanks!
Look under the right front wheel arch to see the wire harness. You might be able to reach down beside the oil filler neck, I
forget.
Kevin
Look under the right front wheel arch to see the wire harness. You might be able to reach down beside the oil filler
neck, I forget.
Kevin